? Controller supplier 24V controller with timer indicator ? DESCRIPTION The BEETLE BT-1 is a low cost gasoline/diesel GENSET control unit designed to start and stop a GENSET both manually and automatic/remotely. The manual control is made using MANUAL and STOP push buttons on the front panel.The remote control is made via REMOTE START input signal at AUTO/REMOTE model. When MANUAL button is pressed, the engine will be cranked up to times. When it runs, the crank relay will be immediately deactivated and after timer delay, fault checking will be enabled. When the engine is running, if a fault condition is detected then the engine is shut down immediately and the LCD display the source, any failure can through alarm led show. The PAGE/SETUP button selects display parameter scroll and allows setup mode entry by keep pressed over 5 second. The unit provides a set of digitally adjustable program parameters. All parameters are modified through front panel pushbuttons. The FUEL output is programmable for ‘Activate to start’ or ‘Activate to stop’ solenoids. The optional auxiliary outputs may be programmed for alarm, choke, preheat or stop functions. ? ? KEY FEATURES ? ? 128*64 pixel back-light LCD graphic display ? LED and LCD alarm indication ? 4 discrete inputs ? 2 discrete Relay outputs and 2 discrete N-MOFET outputs ? Configurable timers and alarms + protection ? Alarm event and message display ? Magnetic Pick-up or charger coil speed sensing ? Engine and alternator alarm + protection ? Charge Alternator failure warning ? KW overload protection ? Fully configurable via by field operations ? Configurable display languages ? Copy setup data to other BEETLE or Computer via service port ? Customized and firmware upgrade via service port by user ??????? Both Manual and remote control ??????? Generator protection ??????? Built in alarms and warnings ??????? Remote Start operation available ? ?

? SPECIFICATION
TEMPERATURE	Cold test -30 ℃ to dry heat +70 ℃
VIBRATION	Ten sweeps in each of three major axes 5 Hz to 8 Hz +/-7.5 mm, 8 Hz to 500 Hz 2 gn
HUMIDITY	Db Damp Heat Cyclic 20/55 ℃ 95% RH 48 Hours Cab Damp Heat Static 40 ℃ 93% RH 48 Hours
DC SUPPLY	6 V to 16 V continuous
MAXIMUM OPERATING CURRENT	150 mA at 12 V
MAXIMUM STANDBY CURRENT	80 mA at 12 V
ANALOG INPUTS	9 INPUT
DISCRETE INPUTS	4 INPUT
DISCRETE OUTPUTS	2* N-MOFET (negative pulling) output 2A max 2*20 A16V DC to relay
COMMUNICATION	Service port 3.3V TTL UART 9600bps,n,8,1
GENERATOR
VOLTAGE RANGE: CURRENT RANGE:	15 V - 350 V AC (L-N) 0mA – 50mA AC (CT:20mA)
MAINS VOLTAGE RANGE	15 V - 350 V AC (L-N)
FREQUENCY RANGE	10 Hz to 75 Hz
MAGNETIC PICK UP/CHARGER COIL VOLTAGE RANGE: FREQUENCY RANGE:	? +/- 1.5 V to 70 V AC 10,000 Hz (max)
DIMENSIONS OVERALL	? 106mm x 59 mm x 33mm
PANEL CUTOUT	92 mm x 44 mm
MAXIMUM PANEL THICKNESS	2 mm
TECHNICAL SPECIFICATIONS
Alternator voltage:	15 to 350 V-AC (Ph-N)
Alternator frequency:	50 or 60 Hz nominal
Measurement Accuracy:	0.5% + 1 digit
Maximum Operating Current:	150 mA-DC
Fuel and Crank outputs:	20A 12V-DC
DC Supply Range:	6.0 to 16.0 V-DC
Cranking dropouts:	survives 0 V for 100ms
Typical Standby Current:	20 mA-DC (display off)
Magnetic pickup Input:	1.5 to 70Vpp
Auxiliary Output:	2A 12V-DC (negative pulling N-MOSFET output)
Operating temp:	-30 ℃ to +70 ℃
Maximum humidity:	95% non-condensing
Dimensions:	104 x 59 x 33 mm (W x H x D)
Panel Cut-out Dimensions:	92x44 mm minimum
Packed weight:	150 g
Case Material:	High Temp. ABS/P
IP Protection:	IP65 (front panel), IP30 (rear)
Installation:	Flat surface mounting on a Type 1 enclosure
Conformity:	(EU directives) -2006/95/ EC (low voltage) -2004/108/EC (EMC)
Norms of reference:	EN 61010 (safety requirements) EN 61326 (EMC requirements)

? ? ? Product photos: ? ? ? Company introduction: ? Office building: ? Factory area:
? Team work:
? Certificates: ? ? Exhibitions: ? Tangpower in USA Time Square: ? Welcome to consult and visit us, Tangpower, any time, any where! ?